- 您现在的位置：买卖IC网 > Sheet目录970 > CPC1009N (IXYS Integrated Circuits Division)RELAY OPTOMOS SP-NO 150MA 4-SOP
I NTEGRATED C IRCUITS D IVISION
CPC1009N
Manufacturing Information
Moisture Sensitivity
All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated
Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to
the latest version of the joint industry standard, IPC/JEDEC J-STD-020 , in force at the time of product
evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper
operation of our devices when handled according to the limitations and information in that standard as well as to any
limitations set forth in the information or standards referenced below.
Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced
product performance, reduction of operable life, and/or reduction of overall reliability.
This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according
to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033 .
Device
CPC1009N
Moisture Sensitivity Level (MSL) Rating
MSL 3
ESD Sensitivity
This product is ESD Sensitive , and should be handled according to the industry standard JESD-625 .
Reflow Profile
This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020
must be observed.
Device
CPC1009N
Maximum Temperature x Time
260oC for 30 seconds
Board Wash
IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to
remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as
an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary
if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used.
Cleaning methods that employ ultrasonic energy should not be used.
Pb
e 3
R05
www.ixysic.com
5
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
CPC1014N
RELAY OPTOMOS 400MA SPST 4-SOP
CPC1016N
RELAY OPTOMOS SP-NO 100MA 4-SOP
CPC1017N
RELAY OPTOMOS SP-NO 100MA 4-SOP
CPC1018N
RELAY OPTOMOS 600MA 4-SOP
CPC1020N
RELAY OPTOMOS 1200MA 4-SOP
CPC1025N
RELAY OPTOMOS 120MA 4-SOP
CPC102K
CORD PATCH COMBINATION 6 FEET
CPC1030N
RELAY OPTOMOS SP-NO 120MA 4-SOP
相关代理商/技术参数
CPC1009NTR
功能描述:固态继电器-PCB安装 Dual 1-Form-A relay RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT
CPC100AFC
功能描述:板上安装压力/力传感器 ASG/SENSYM RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides
CPC100AFH
功能描述:板上安装压力/力传感器 ASG/SENSYM RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides
CPC100GC
功能描述:板上安装压力/力传感器 ASG/SENSYM 130 - CPC,CPCL
RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides
CPC100GFC
功能描述:板上安装压力/力传感器 ASG/SENSYM
RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides
CPC100GFH
功能描述:板上安装压力/力传感器 ASG/SENSYM RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides
CPC100SS6
制造商:Thomas & Betts 功能描述:SS316 1 COBRA CLAMP
CPC1010N
功能描述:Solid State Relay SPST-NO (1 Form A) 4-SOP (0.150", 3.81mm) 制造商:ixys integrated circuits division 标准包装:100